Changing a Garment From Zippered to Buttoned

I have a customer who loathes zippers in her robes.

So, she asked me if I could take the zipper out and put in buttons.

No problem, I answered.

It’s no problem because I made sure that she understood that she was going to lose some of the width in the front.

Putting in buttonholes and buttons means one side will overlap the other (just like a shirt does) when I am finished.

In the case of this robe, the “chevron” angles won’t ever meet in the middle again either.

But that was fine with my customer.

She just wanted buttons.

Here’s the robe:

sewing blog 327

The good news is that the garment you work on most likely won’t be this fussy.

You’ll probably be working with a solid colered garment, or at least one that doesn’t have stripes going on the diagonal.

To begin with, remove the zipper with your seam ripper.

sewing blog 328

On this robe, there is a facing on the inside top of the robe and the zipper is sandwiched inside of it.

So, if you have a facing in your shirt, robe or other garment, you’ll need to rip out the facing and then the zipper. Sometimes you can take out both at the same time.

For this illustration, I decided to take off the facing first and then peel back the zipper like this:

sewing blog 329

Once you have the zipper out, you notice that this garment did not separate in two.

That’s because the zipper didn’t go all the way to the hem of the robe.

So, we need to open the robe up.

To do this, I lay a cutting mat in between the layers (so I don’t cut the back of the robe by accident) and use a rotary cutter and long ruler to cut the robe open.

Line up the ruler perpendicular to the hem and make sure it lines right up to the zipper opening.

And then cut it:

sewing blog 330

Once you’ve cut the opening, look to see if you’ve cut across any seams.

If you have, you need to anchor those so that they don’t come undone as you work on your garment.

I was able to just topstitch on these seams:

sewing blog 332

Take a few stitches out of the hem so that you can open that area up to work on it later.

sewing blog 333

Serge the raw edges if you have a serger.

If you don’t, zig zag the raw edges so they don’t unravel:

sewing blog 334

To make the facing, cut a piece of fabric about 2 1/2″ wide and as long as the length of the front of the robe.

Cut some iron on interfacing a little narrower and a little shorter than the facing strip, so that when you press it on, it doesn’t stick to the iron or the ironing board.

Now press the interfacing onto the wrong side of the facing strip.

sewing blog 363

Lay the facing strip right sides together down the front edge of the robe.

sewing blog 366

Do you see the facing that is hanging free in the photo above? Just fold that over and make sure it will cover the top edge of the facing strip. In the photo below you can see that when the original facing is folded over, it will cover the white facing strip after it is sewn.

So pin it in place like in the photo above and stitch it down.

sewing blog 367

Now pin the original facing to the facing strip being careful not to cathc the front of the robe in the pin.

sewing blog 372

Open this area out flat and stitch it in place so that you don’t catch the front of the robe in the stitching like this:

sewing blog 373

At the bottom of the robe, trim off the white facing strip even with the folded bottom edge of the robe.

sewing blog 371

Open out the hem and facing. Take the bottom edge of the hem and fold it up right sides together onto itself and pin in place

sewing blog 374

Stitch along that seam line (in the above photo) where the pin is. Of course, you don’t want to stitch over the pin! I just put it there so you could see the line better.

When you turn it right side out, it should look like this:

sewing blog 376

Now stitch the hem by hand or machine.

Next, make buttonholes of whatever size you’d like based on the size of buttons you chose.

I am not including  instructions on making buttonholes because every machine is different and some have built in buttonhole makers.

So check your sewing machine’s instruction manual.

Sew on the buttons with a thread shank if you need it.

I realize every garment is a little different than the one I just explained, but the technique should be applicable to what you are working on.

Enjoy your “new” garment!

Advertisements

2 Responses

  1. Have you ever done the opposite of this?

    • It seems like I have once before. The only problem is that you have to take out the buttonholes and that might not leave you with enough circumference around the robe or garment. You most likely will need to remove any facing he garment has as well. It’s time consuming, but doable.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s